Factory Installed Options

$1,000.00

50% more cooling capacity Higher speed & proper water pressure Low water pick-up 50% more volume than any now on the market. Nose cone kit contains all hardware for complete installation Kit comes complete with ALMAG-35 top grade casting,…

Description

We offer many more cones as a Factory option.  They are a modified version of the kits we sell, but the installation is done differently, sometimes for certain boats we centerline the cone purpose built for speed, or in some cases leave the bottom 2 factory holes open.

Note the price is for a single hose bigfoot on most motors, prices range from $554-680 depending on cone and motor.

We can install torque tabs, repair skegs, straighten prop shafts, and paint to suit.  Most options are shown here, but not all, please call us to discuss your needs, and we will make a custom installation ready for you.

You just simply disconnect your lower unit, drain the oil and ship to us.  If you don’t have a packing method, we can send to you an empty box for $20 which we then put as a credit towards you install when we receive the lower unit.

  • 50% more cooling capacity

  • Higher speed & proper water pressure

  • Low water pick-up

  • 50% more volume than any now on the market.

  • Nose cone kit contains all hardware for complete installation

  • Kit comes complete with ALMAG-35 top grade casting, epoxy, hose fittings and instructions.

  • Crescent shaped for superior and handling

  • Five inlets create less chance of stoppage than anything now on the market.

  • includes fresh water flush kit

Proven Quality
The same superior design as our World Speed Record Holding Big Foot, low water pick-up cones.

High Water Flow Capacity
Allow surface Piercing props (choppers, cleaver style) to be run at maximum height for top speed and all out performance, while maintaining proper cooling to engine.

Shallow Water Access
Travel and fish waters, until now, were unable to be reaches with outboard motors having standard (side water pick-up) gear cases.

Nose cone test by Bass & Walleye Magazine :

Nose Cone Shootout
Test Results and Fact Sheet

SPEED INCREASE OVER 5 MPH ON A 150 H.P. !!!

 

NOSE CONES TESTED TOP-SPEED M.P.H. MAXIMUM MOTOR-HEIGHT
OBTAINED ABOVE TRANSOM WHILE MAINTAINING 10 PSI WATER PRESSURE MINIMUM
R.P.M. OBTAINED WITHOUT PROP SLIPPAGE
BOB’S 74.8 Sky High 6250
HYDRO MOTIVE 72.5 3-1/2 inches 6150
LAND & SEA 70.1 2-1/4 inches 5850
MERCURY STOCK 69.7 2-1/2 inches 5900
MERCURY CLS (RACING) 68.5 No limit 6150

REMEMBER: THE TRUTH IS AN UNDENIABLE FACT.

 

Test performed and documented by the Technical Department of an unbiased
major boating magazine, Bass & Walleye Boats, fall issue NOSECONE SHOOTOUT.

TEST BOAT and EQUIPMENT USED

BOAT:
Nitro 190 TF (19 ft. bass boat)
MOTOR:
Mercury 150XRI 150 horsepower
GEARCASE:
1.87:1 ratioLOAD:
Two 200 pound men; 28 gallons of fuel, near full livewell (half full) 
PROP:
Quicksilver trophy, four blade, small-hub, 13 3/8 x 25 inch pitch
SPEED:
Radar checked (Stalker Radar Gun)CONDITIONS:
Test held in under four hours with conditions at the start virtually the same as at the end. Flat to 2 inch chop, no wind, with 58 degree’s Fahrenheit air temperature.

Shipping dimensions & weights

Weight 100 lbs
Dimensions 19 × 13 × 5 in

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.