Snap back fit all head sizes.

The post Bob’s Floral Hat first appeared on Bob's Machine.

Snap back fit all head sizes.

The post Bob’s RealTree Camo Hat first appeared on Bob's Machine.

Snap back fit all head sizes.

The post Bob’s Gulf Racing Themed hat first appeared on Bob's Machine.

Exhaust Housing – Mercury for 3.0L V6 motors

Exhaust Housing designed for Outboards

Without modification to the engine, this simple, after-market add-on is designed to relieve back pressure on the engine, and results in more efficient low-end throttle response, a better tuned engine and increase fuel economy.

The unit comes complete with two removable plugs and four screws, so the casting can be installed on the back of your motor.

By removing two plugs the unit will allow exhaust which normally travels through the propeller to escape above the water line, and consequently this results in your engine breathing and performing better. Replace the plugs in the unit and exhaust will travel through the prop again.

Requires drilling into midsection.

The post Exhaust Housing – Mercury 3.0L V6 first appeared on Bob's Machine.

Engineered for the most demanding conditions, the rugged Everflex® spike is virtually indestructible, seamlessly stowing itself into the pocketed design of this aerodynamic-inspired model with swift, silent efficiency. Maximize your on-water adventures with our Blade Edition shallow water anchor – a testament to toughness and optimized for durability. Step up your game and harness the power of the Blade Edition today.

Features:
• Fastest stopping time
• Aerodynamic design
• Soft Close System
• Extremely lightweight
• Reinforced stern bracket
• Available up to 10ft in length
• Marine grade powder coated finish
• Down and away deployment
• Built-In drive off protection
• Quick and easy installation

Dual Blade ONE Pump Includes:
• (2) Blade Anchors
• (2) ONE Wireless Remotes
• Mountable Remote Cradle
• ONE Dual Anchor Pump
• HD Hydraulic Hoses

Individual Blade Pump Includes:
• 2-button key remote
• Advanced Dash Switch
• Upgraded Hydraulic Pump (HPU)
• HD Hydraulic Hoses

The post Power Pole Blade 1 Pump first appeared on Bob's Machine.

Garmin, Humminbird, Navico (Simrad/Lowrance) & Raymarine compatible.  Please make sure to check your units compatibility & software version to make sure Jack Plates are supported, many older units do not have the newest software updates available to integrate.

Connect your Bob’s Machine jack plate to your Multi-Function Display and view your jack plate height.  Has functionality to allow MFD to control jack plates, waiting on MFD brands to make changes to their programing to allow.

Majic Sync, Multi-Actuator Jack-plate Integration Controller, Keeps up to 5 jack plates in Sync with each other via digital controls.  This allows rigging teams easier installation of multi engine jack plates without complicated hydraulic valving, or multiple switches for the operator.

Bob’s new Majic Sync utilizes NMEA connections allowing MFDs to control the jack plate height, as well as view height on the MFD in place of a traditional Gauge.  The Majic Sync still allows traditional gauges and switch to be used as well.

In event of a jack plate or sending unit failure, The Majic Sync also utilizes WiFi technology so the boater can access the Majic Sync via their phone and use the manual override feature to adjust individual jack plates.  The WiFi Connection also allows easy firmware updates to the unit.

If you wish to add a physical gauge to your dash, please also add https://bobsmachine.com/product/jack-plate-gauge-only/ to your order.

The post MAJIC Sync- Multi Jack plate Controller for up to 5 jack plates first appeared on Bob's Machine.

Bob’s Kick-Back Plate

The best jack plate available meets the KickBack plate to form the new Hydraulic KickBack Jac!  Bob’s jack plate with 6″ hydraulic stroke and 1.5″ built in structure lift offering a total of 7.5″ total lift!  Delrin bushing throughout provide long life of smooth sliding, and pivoting.  Navigate the shallows, and if you encounter a submerged object, you can jack up your motor and idle over allowing your motor to KickBack and prevent costly damage to the lower unit.

Features :

1. Patent pending
2. 4″ Setback
3. Locking pins for reverse
4. Grease able pivot points and slide plate area
5. No spring or chains
6. Tension rods
7. 30 deg of tilt
8. Delrin rollers and bearings for smooth operation; No need for chains or spring
9. Motor tether attachment point for safety
10. Locking pins to prevent plate from kicking out in reverse or trailering
11. Grease able pivot points – automotive zerk fittings
12. Rated up to 150 HP motors – BIA bolt pattern
13. Unit weight : 48 LBS
14. Limited Lifetime Structure Warranty against manufacturing defects
15. 3 Year Action Pump Warranty

WARNING: This unit is rated for outboard motors up to a maximum of 150 H.P. Do not encounter obstructions at speeds over 5 M.P.H and only in the forward direction. It is not designed or intended to encounter obstructions while the boat is being operated in the reverse direction.

The post 4″ Hydraulic Action Series Kick-Back Jac first appeared on Bob's Machine.

Coming soon for other trolling motors.

Not just a kickstand, but a fully locking trolling motor mount.  Keeps your investment safe and secure.

Machined from 6061 aluminum, these are built to last.  Featuring a ball and socket design, your trolling motor will latch into place.

Requires drilling a 1 & 7/8″ hole in your deck.  The head bolts into factory predrilled & tapped holes on power pole move.

If you dont want to drill into deck, you can just use the kickstand portion.

Includes all mounting hardware.

The post Trolling Motor LockDown – Power Pole Move first appeared on Bob's Machine.

Bolt Kit for jack plate installation – For motors with 1/2″ hardware requirements.  Not for Mini Manual Jack Plate

304SS

Contains:

6 x 1/2″ SS Bolts

6-1/2″ Nylok Nuts

12 x Flat washers

6 x Lock Washers

The post Transom/Engine Bolt Kit : Set of 6 Pick your size first appeared on Bob's Machine.

Please note – on the the colored units are just to show color!  Multiple sizes shown.

The first race specific jack plate from Bob’s, and the first ever race specific vertical lift jack plate with Hydraulic options!

Standard series – Remote mount pump with hoses – 6″ Adjustable travel

Versa series – Manual screw jack – 6″ Adjustable travel

Transom side plate with patent pending interlocking system to the side rails.  Machined excess material off of plate to save weight!

The post 12″ Race Series Jack Plate first appeared on Bob's Machine.