The Bigfoot nose cone is our most performance oriented unit, with the pickup holes only on the bottom of the bullet.  This allows the motor to be raised extremely high and still maintaining water pressure.  For most V6, or raced units we recommend our Dual hose version of this cone.  If you need a recommendation for which style of nose cone is right for you, please give us a call or email.

If you are using a smaller motor or the Mercury Inline gear case, please choose the ‘inline’ option, it is a shorter unit.  Rule of thumb is any engines 90 hp or smaller need the inline kit.  If you are smaller than 60hp, please call first, as the cone will require modification to work, and you might perfer to send in for factory installation.

• 50% more cooling capacity

• Higher speed & proper water pressure

• Low water pick-up

• 50% more volume than any now on the market.

• Nose cone kit contains all hardware for complete installation

• Kit comes complete with ALMAG-35 top grade casting, epoxy, hose fittings and instructions.

• Crescent shaped for superior and handling

• Five inlets create less chance of stoppage than anything now on the market.

• Includes freshwater flush kit

Proven Quality
The same superior design as our World Speed Record Holding Big Foot, low water pick-up cones.

High Water Flow Capacity
Allow surface Piercing props (choppers, cleaver style) to be run at maximum height for top speed and all out performance, while maintaining proper cooling to engine.

Shallow Water Access
Travel and fish waters, until now, were unable to be reaches with outboard motors having standard (side water pick-up) gear cases.

Nose cone test by Bass & Walleye Magazine :

Nose Cone Shootout
Test Results and Fact Sheet

Test performed and documented by the Technical Department of an unbiased
major boating magazine, Bass & Walleye Boats, fall issue NOSECONE SHOOTOUT.

MOTOR:
Mercury 150XRI 150 horsepower

GEARCASE:
1.87:1 ratio

LOAD:
Two 200 pound men; 28 gallons of fuel, near full livewell (half full)

PROP:
Quicksilver trophy, four blade, small-hub, 13 3/8 x 25 inch pitch

SPEED:
Radar checked (Stalker Radar Gun)

CONDITIONS:
Test held in under four hours with conditions at the start virtually the same as at the end. Flat to 2 inch chop, no wind, with 58 degree’s Fahrenheit air temperature.

The post Bigfoot Nose Cone Kit : 20-450 HP first appeared on Bob's Machine.

The Combo cone is our most popular sport fisher model.  It has 5 inlets on the bottom of the bullet, and 4 holes above the bullet.  The intakes “suck” where you put them, so if in shallow water you can block the lower ones, but the top will always remain open.  Once you get up and moving again the lower will flush out and be fine. If you need a recommendation for which style of nose cone is right for you, please give us a call or email.

If you are using a smaller motor or the Mercury Inline gear case, please choose the ‘inline’ option, it is a shorter unit.  Rule of thumb is any engines 90 hp or smaller need the inline kit.  If you are smaller than 60hp, please call first, as the cone will require modification to work, and you might perfer to send in for factory installation.

• 50% more cooling capacity

• Higher speed & proper water pressure

• Low water pick-up

• 50% more volume than any now on the market.

• Nose cone kit contains all hardware for complete installation

• Kit comes complete with ALMAG-35 top grade casting, epoxy, hose fittings and instructions.

• Crescent shaped for superior and handling

• Five inlets create less chance of stoppage than anything now on the market.

• Includes fresh water flush kit

Proven Quality
The same superior design as our World Speed Record Holding Big Foot, low water pick-up cones.

High Water Flow Capacity
Allow surface Piercing props (choppers, cleaver style) to be run at maximum height for top speed and all out performance, while maintaining proper cooling to engine.

Shallow Water Access
Travel and fish waters, until now, were unable to be reaches with outboard motors having standard (side water pick-up) gear cases.

Nose cone test by Bass & Walleye Magazine :

Nose Cone Shootout

Test Results and Fact Sheet

Test performed and documented by the Technical Department of an unbiased
major boating magazine, Bass & Walleye Boats, fall issue NOSECONE SHOOTOUT.

MOTOR:
Mercury 150XRI 150 horsepower

GEARCASE:
1.87:1 ratio

LOAD:
Two 200 pound men; 28 gallons of fuel, near full livewell (half full)

PROP:
Quicksilver trophy, four blade, small-hub, 13 3/8 x 25 inch pitch

SPEED:
Radar checked (Stalker Radar Gun)

CONDITIONS:
Test held in under four hours with conditions at the start virtually the same as at the end. Flat to 2 inch chop, no wind, with 58 degree’s Fahrenheit air temperature.

The post Combo Nose Cone Kit : 20-450 HP first appeared on Bob's Machine.

The Shallow Runner nose cone is for the guys constantly dragging their lower unit through sand and mud.  If there is NO paint on your skeg, this is probably a good choice!  The water pickups are only on top of the bullet.  If you need a recommendation for which style of nose cone is right for you, please give us a call or email.

If you are using a smaller motor or the Mercury Inline gear case, please choose the ‘inline’ option, it is a shorter unit.  Rule of thumb is any engines 90 hp or smaller need the inline kit.  If you are smaller than 60hp, please call first, as the cone will require modification to work, and you might prefer to send in for factory installation.

• 50% more cooling capacity

• Higher speed & proper water pressure

• Low water pick-up

• 50% more volume than any now on the market.

• Nose cone kit contains all hardware for complete installation

• Kit comes complete with ALMAG-35 top grade casting, epoxy, hose fittings and instructions.

• Crescent shaped for superior and handling

• Four inlets create less chance of stoppage than anything now on the market.

• Includes Freshwater flush kit

Proven Quality
The same superior design as our World Speed Record Holding Big Foot, low water pick-up cones.

High Water Flow Capacity
Allow surface Piercing props (choppers, cleaver style) to be run at maximum height for top speed and all out performance, while maintaining proper cooling to engine.

Shallow Water Access
Travel and fish waters, until now, were unable to be reaches with outboard motors having standard (side water pick-up) gear cases.

Nose cone test by Bass & Walleye Magazine :

Nose Cone Shootout
Test Results and Fact Sheet

Test performed and documented by the Technical Department of an unbiased
major boating magazine, Bass & Walleye Boats, fall issue NOSECONE SHOOTOUT.

The post Shallow Runner Nose Cone Kit : 20-450 HP first appeared on Bob's Machine.