Bob’s Kick-Back Plate

The best jack plate available meets the KickBack plate to form the new Hydraulic KickBack Jac!  Bob’s jack plate with 6″ hydraulic stroke and 1.5″ built in structure lift offering a total of 7.5″ total lift!  Delrin bushing throughout provide long life of smooth sliding, and pivoting.  Navigate the shallows, and if you encounter a submerged object, you can jack up your motor and idle over allowing your motor to KickBack and prevent costly damage to the lower unit.

Features :

1. Patent pending
2. 4″ Setback
3. Locking pins for reverse
4. Grease able pivot points and slide plate area
5. No spring or chains
6. Tension rods
7. 30 deg of tilt
8. Delrin rollers and bearings for smooth operation; No need for chains or spring
9. Motor tether attachment point for safety
10. Locking pins to prevent plate from kicking out in reverse or trailering
11. Grease able pivot points – automotive zerk fittings
12. Rated up to 150 HP motors – BIA bolt pattern
13. Unit weight : 48 LBS
14. Limited Lifetime Structure Warranty against manufacturing defects
15. 3 Year Action Pump Warranty

WARNING: This unit is rated for outboard motors up to a maximum of 150 H.P. Do not encounter obstructions at speeds over 5 M.P.H and only in the forward direction. It is not designed or intended to encounter obstructions while the boat is being operated in the reverse direction.

The post 4″ Hydraulic Action Series Kick-Back Jac first appeared on Bob's Machine.

The post Replacement Kick Back Jac Pin first appeared on Bob's Machine.

New Action series Tilt and Trim, all in one unit!  Easy rigging and tons of benefits!

For outboard owners without factory tilt and trim, Bob’s Machine Shop has a solution. Designed for motors up to 115hp (BIA Bolt Pattern), BMS’s hydraulic Tilt & Trim can provide increased performance, better handling and less hassle raising and lowering the motor at the launch ramp.

The Tilt & Trim allows boat operators to trim the boat for a smoother, drier ride. When fully trimmed in, it provides a faster start and quicker on-plane time. After reaching plane, the boat can be optimized for best running angle by trimming the tilt up to its maximum of 65 degrees. 6-inch setback is standard.

BMS’s Tilt & Trim is easy to install. It comes with wiring harness, control switch and carries a limited lifetime structural warranty. 

Includes trim plate, wiring harness, relays, rocker style switch

Limited Lifetime Structure Warranty against manufacturing defects

3 Year Action Pump Warranty

Transom Weight – 43lbs

Call for other powder coating and hydrographic options!

The post BIA bolt on Motor Tilt and Trim (Action Series) first appeared on Bob's Machine.

The best jack plate available meets the KickBack plate to form the new Versa KickBack Jac!  Bob’s jack plate with 6″ adjustable manual jackplate with 1.5″ built in structure lift offering a total of 7.5″ total lift!  Delrin bushing throughout provide long life of smooth sliding, and pivoting.  Navigate the shallows, and if you encounter a submerged object, you can jack up your motor and idle over allowing your motor to KickBack and prevent costly damage to the lower unit.

Features :

1. Patented design
2. 6″ Setback
3. Locking pins for reverse
4. Grease able pivot points and slide plate area
5. No spring or chains
6. Tension rods
7. 30 deg of tilt
8. Delrin rollers and bearings for smooth operation; No need for chains or spring
9. Motor tether attachment point for safety
10. Locking pins to prevent plate from kicking out in reverse or trailering
11. Grease able pivot points – automotive zerk fittings
12. Rated up to 150 HP motors – BIA bolt pattern
13. Unit weight : 48 LBS
14. Limited Lifetime Structure Warranty against manufacturing defects

WARNING: This unit is rated for outboard motors up to a maximum of 150 H.P. Do not encounter obstructions at speeds over 5 M.P.H and only in the forward direction. It is not designed or intended to encounter obstructions while the boat is being operated in the reverse direction.

The post 6″ Versa Series Kick-Back Jac first appeared on Bob's Machine.

Bob’s Kick-Back Plate

The best jack plate available meets the KickBack plate to form the new Hydraulic KickBack Jac!  Bob’s jack plate with 6″ hydraulic stroke and 1.5″ built in structure lift offering a total of 7.5″ total lift!  Delrin bushing throughout provide long life of smooth sliding, and pivoting.  Navigate the shallows, and if you encounter a submerged object, you can jack up your motor and idle over allowing your motor to KickBack and prevent costly damage to the lower unit.

Features :

1. Patented design
2. 6″ Setback
3. Locking pins for reverse
4. Grease able pivot points and slide plate area
5. No spring or chains
6. Tension rods
7. 30 deg of tilt
8. Delrin rollers and bearings for smooth operation; No need for chains or spring
9. Motor tether attachment point for safety
10. Locking pins to prevent plate from kicking out in reverse or trailering
11. Grease able pivot points – automotive zerk fittings
12. Rated up to 150 HP motors – BIA bolt pattern
13. Unit weight : 48 LBS
14. Limited Lifetime Structure Warranty against manufacturing defects
15. 3 Year Action Pump Warranty

WARNING: This unit is rated for outboard motors up to a maximum of 150 H.P. Do not encounter obstructions at speeds over 5 M.P.H and only in the forward direction. It is not designed or intended to encounter obstructions while the boat is being operated in the reverse direction.

The post 6″ Hydraulic Action Series Kick-Back Jac first appeared on Bob's Machine.

Features :

1. 28 LBS total weight
2. Width – 17.5”
3. Height – 12”
4. Offset – 5.5”
5. 45 deg tilt up (kick up)
6. Delrin rollers and bearings for smooth operation; No need for chains or spring
7. Motor tether attachment point for safety
8. Locking pins to prevent plate from kicking out in reverse or trailering
9. Grease able pivot points – automotive zerk fittings
10. Patent pending
11. Rated up to 115 HP motors – BIA bolt pattern
12. Optional clamp on style kit available. Item number is 100-105001

WARNING: This unit is rated for outboard motors up to a maximum of 115 H.P. Do not encounter obstructions at speeds over 5 M.P.H and only in the forward direction. It is not designed or intended to encounter obstructions while the boat is being operated in the reverse direction.

The post Kick-Back Plate first appeared on Bob's Machine.

Bob’s Machine Shop’s new Patented combo tilt and jack aka The Versa Tilt & Jac!

This unit doubles as both a tilt and trim, and a jack plate

Tilt is Hydraulic powered with remote mount pump (like a power pole)

Jack Plate is Manual adjust.

The unit is rated for 50HP, and can be either clamp on, or BIA bolt on pattern.

Unit includes the plate, hydraulic pump, hoses, switch, wiring harness, and oil.

The post Versa Tilt & Jac – A Unique tilt & jack plate combo unit! first appeared on Bob's Machine.

SET OF STACKABLE SPACERS (6) FOR TILT & TRIM/CLAMP ON ENGINE

These are a great solution for clamp on motors that don’t screw down far enough to grab a jack plate, tilt trim, or thin transom.  Much better looking and stronger than a piece of wood that is commonly seen!

The post Set of Stackable Spacers first appeared on Bob's Machine.

New Action series Tilt and Trim, all in one unit!  Easy rigging and tons of benefits!

For outboard owners without factory tilt and trim, Bob’s Machine Shop has a solution. Designed for motors up to 30hp(clamp on style only), BMS’s hydraulic Tilt & Trim can provide increased performance, better handling and less hassle raising and lowering the motor at the launch ramp.

The Tilt & Trim allows boat operators to trim the boat for a smoother, drier ride. When fully trimmed in, it provides a negative 3-degree tuck-under angle for faster starts and quicker on-plane times. After reaching plane, the boat can be optimized for best running angle by trimming the tilt up to its maximum of 65 degrees. A 5-1/2 inch setback is standard.

The hydraulically operated Tilt & Trim will accommodate clamp-on motors, not standard BIA bolt pattern style. Call for questions.

The Over all mounting dimensions, which are: 10″ wide by 11.5″ length

BMS’s Tilt & Trim is easy to install. It comes with wiring harness, control switch and carries a limited lifetime structural warranty. 

Includes trim plate, wiring harness, relays, rocker style switch

Limited Lifetime Structure Warranty against manufacturing defects

3 Year Action Pump Warranty

Stackable spacers for the clamps included standard!

Call for other powder coating and hydrographic options!

The post Clamp-on Motor Tilt and Trim (Action Series) 30HP first appeared on Bob's Machine.

Bob’s Machine Shop’s new Patented combo tilt and jack aka The Tilt & Jac!

This unit doubles as both a tilt and trim, and a jack plate, and is powered by one internal (mounted inside the boat) hydraulic pump.

There are two hydraulic cylinders in the plate, and via a hydraulic solenoid valve, a flip of a switch changes between tilt & jack.

The unit is rated for 50HP, and can be either clamp on, or BIA bolt on pattern.

Unit includes the plate, hydraulic pump, hoses, switch, solenoid valve, wiring harness, oil, it is a complete kit.

Product’s transom weight is 40 lbs.

The post Tilt & Jac – A Unique tilt & jack plate combo unit! first appeared on Bob's Machine.